- 8184663363
- aacaliforniaroofing@gmail.com
- License : #1147688
We use cookies and measurement tools from Google to measure our ads and improve this site. By continuing to browse, you agree. You can change this anytime. Privacy Policy
AA California Roofing does flat roof repair in Los Angeles: we fix ponding, blistered or split torch-down and modified-bitumen membranes and failed seams, and we install new torch-down systems when the old roof is done. We work on flat and low-slope roofs on homes, additions and commercial buildings. CSLB license #1147688; estimates are free.
Book a flat roof inspection through our contact page; we are open Sunday to Friday, 8 AM to 8 PM. We cover all of Los Angeles County, from the San Fernando Valley to the coast, plus Simi Valley, Thousand Oaks, Moorpark, Camarillo and Oxnard.
A “flat” roof is never truly flat. The Energy Code calls it low-sloped: a pitch under 2:12, meaning less than 2 inches of rise per foot of run. That shallow slope is why these roofs use continuous membranes instead of overlapping shingles or tiles, and why they fail in different ways.
New membranes and white coatings on flat roofs we have worked on. Open a project to see every photo and what we did.
On a Los Angeles house, the usual flat roof choices are a torch-down modified bitumen membrane, a single-ply membrane such as TPO, or a coating over the roof that is already there. Torch-down and TPO are complete roof systems. A coating only renews the surface, and only when the membrane under it is still dry and well bonded. Which one fits depends on what is under the surface, how the roof drains and the cool-roof rules for your ZIP code.
We repair and install torch-down and modified bitumen roofs, and we recoat roofs that pass that dry-and-bonded check. If your roof is TPO now, or a bid you hold proposes it, tell us when you book and we will say whether it is work we take on.
The California Residential Code gives each flat roof covering its own section: built-up roofing (two or more layers of felt cemented together and surfaced with a cap sheet, gravel or a coating), modified bitumen (polymer-modified asphalt sheets; torch-down is the torched kind), single-ply membranes such as TPO, PVC and EPDM, spray foam, and liquid-applied roofing. Roof coatings have a section of their own.
| On a Los Angeles flat roof | Torch-down (modified bitumen) | TPO (single-ply) | Roof coating |
|---|---|---|---|
| What it is | Polymer-modified asphalt sheets, usually a base sheet under a granulated cap sheet | One layer of reinforced thermoplastic polyolefin sheet | A liquid (acrylic, silicone, polyurethane or asphalt-based) over the existing roof. It renews a roof; it is not a new one |
| How it is installed | Each sheet is heated with a propane torch and fused down. The fire code treats this as hot work: a fire watch during the work and for at least 30 minutes after it ends (California Fire Code 3504.2.1) | Fastened or adhered to the deck, with the seams welded by hot air. No open flame | Rolled or sprayed on. No flame and no tear-off |
| A new layer without a tear-off? | Only where the manufacturer’s instructions allow it, the old roof is dry and sound, and it has fewer than two coverings already (CRC R908.4). Otherwise a tear-off | The same rule as torch-down | Allowed over existing modified bitumen, built-up or single-ply roofing without a tear-off, but never over a roof that is water-soaked or too worn to be a base |
| Reflective surface (climate zones 4 and 6 to 15) | The cap sheet, or a coating over it, must reach an aged solar reflectance of 0.63 with a thermal emittance of 0.75, or an SRI of 75, on its CRRC rating; extra deck insulation can take its place | Sold in white and other colors; the exact product’s aged CRRC rating has to meet the values | The Energy Code’s re-roof rule includes “adding a new surface layer”, so a coating over more than half the roof should be a CRRC-rated reflective product |
| R-14 insulation on a replacement in zone 9 (Woodland Hills, Van Nuys, Pasadena); none in zone 6 (Santa Monica, Torrance, Long Beach) | Required unless an exception applies, so flashings, drains and curbs may have to be raised to suit | Required too, unless an exception applies: a white surface answers the reflectance rule, not the insulation rule | On its face, the code’s wording also reaches a coating over more than half the roof. Ask how the permit office applies it before choosing a coating to skip the insulation |
| Standard to ask for on the bid | ASTM D6162, D6163, D6164, D6222, D6223 or D6298 (CRC Table R905.11.2) | ASTM D6878 (CRC Table R905.12) | Acrylic ASTM D6083, silicone D6694, moisture-cured polyurethane D6947, or an asphalt coating standard (CRC Table R909.2) |
| With AA California Roofing | We repair and install it | Ask us first whether we take the job on | We recoat roofs that pass the dry-and-bonded check |
Only on a roof that is still sound enough to be a base for new roofing. A coating does not dry wet insulation or firm up a soft deck; spread over them, it seals the water in, out of sight. Section R908.4 of the 2025 California Residential Code allows a coating over an existing roof without a tear-off, but no recover over a roof that is water-soaked or too deteriorated to be an adequate base. A recoat bid should say how the roof was checked for wet areas; how we check is in the next section.
No reliable number of years fits every flat roof; for the product on yours, its manufacturer’s documentation is the reference. Material warranties are provided directly by the manufacturer and are subject to the manufacturer’s terms. Read the years on any warranty with care: the National Roofing Contractors Association advises that a warranty’s length should not be the main reason to choose a roof system, because it does not assure performance, and that some warranty terms were set without research or field records of how the roof holds up.
Before you choose, check which surface and insulation your address needs: our guide to the cool roof rules for flat roofs has the CRRC values and the City of Los Angeles rule for homes, which sets higher values than the state’s. Offices, shops and apartment buildings are covered on our commercial roofing page.
The decision depends on what is under the surface, not only on what shows on top. Wet insulation and soft decking cannot be seen from the roof, so we check suspect areas by feel and by opening small test spots, and look at the deck from below where it is exposed.
| What we find | Usual answer | Why |
|---|---|---|
| One split seam, a blister or a flashing failure; the rest of the membrane is sound | Repair | The roof has life left; fixing the one failure is enough |
| The surface is worn, but the membrane is dry and well bonded | Recoat with an approved roof coating | Restores UV protection and can add reflectance; LADBS lists coating an existing roof as an express permit |
| The old roof is dry, flat and well attached, with no wet insulation, and the building code allows another layer | Re-cover (a new membrane over the old) | Avoids a full tear-off; the Energy Code still counts a new layer as a roof replacement |
| Wet insulation, a soft deck, repeated leaks, or layers already stacked up | Tear-off and replace | A new layer over trapped moisture rots the deck from below and fails early |
Torch-down is modified-bitumen roofing: asphalt blended with polymers, reinforced with a mat and made in rolls. The installer heats the underside of each roll with a propane torch until the asphalt melts, then rolls it out so it fuses to the layer below and to the edge of the neighboring sheet.
The strengths are fused seams instead of glued ones, a tough surface that handles some foot traffic around rooftop equipment, and repairs that use the same torch-and-patch method. The trade-offs are the open flame, which calls for a careful crew and a fire watch near wood and parapets, and the heat a dark granulated cap absorbs unless it is a cool-rated product. How long the roof lasts depends mostly on drainage, sun exposure and upkeep; standing water shortens it more than anything else.
When more than 50 percent of a home’s low-slope roof is replaced (a new layer over the old one counts), Section 150.2(b)1I of California’s 2025 Energy Code sets two requirements. They cover permits applied for since January 1, 2026.
What that means by address, using the Energy Commission’s ZIP code list: a flat roof in Woodland Hills, Encino, Van Nuys, North Hollywood or Pasadena (zone 9) needs both a reflective cap or coating and R-14 insulation, unless an exception applies. A flat roof in Santa Monica, Torrance or Long Beach (zone 6) needs the reflective surface, but not the insulation. Apartment and commercial buildings follow their own sections of the code. Our cool roof requirements guide explains the rules in more detail.
We price flat roof work after the inspection, because the same roof size can mean a one-seam repair or a full tear-off. These are the items that move the price, and the ones to compare when you read two bids:
Photos from the job, taken by our crew.
Send photos of the problem area to aacaliforniaroofing@gmail.com, or request a visit on our contact page. The estimate is free. For leaks on pitched shingle or tile sections, see our roof repair service; for a whole-house re-roof that includes pitched and flat sections, see roof replacement. Everything else we do is on the AA California Roofing home page.
Explore genuine Google reviews from our satisfied customers and discover why they trust our team for reliable solutions, quality workmanship, and exceptional service.
